wiki:Tutorial/GeometricCalibration

Version 25 (modified by vaillant1p, 6 years ago) (diff)

--

TracNav(Tutorial/TOC)?

Tutorial / Geometric calibration

Simple scaling

Open again a test image in 'UVMAT_DEMO01_pair' (accessible on http://servforge.legi.grenoble-inp.fr/pub/soft-uvmat/).

We shall use the diameter of the half cylinder visible on the upper let of the image to set the calibration. Its physical diameter is 2cm. The corresponding diameter in pixels can be obtained with the ruler displayed by the menu bar [Tools/ruler] of uvmat.

First zoom on the cylinder to optimize the precison. Select [zoom on], press the left mouse button and adjust the field with the directional key board arrows. Then unselect [zoom on] to allow for other mouse actions (otherwise zoom has priority). It is also useful to increase the contrast at the cylinder edge by setting MaxA to 100 in the frame [Scalar] (right side of uvmat).

Then select the menu bar [Tools/ruler], press the left hand mouse button on the cylinder edge, draw a diameter keeping the mouse pressed, release it on the opposite edge. The length in pixels, 140, is displayed, so the scaling factor is 140/2=70 pixels/cm.

Open the menu bar [Tools/geometric calibration]. A new GUI geometry_calib appears on the right side. Activate the upper menu bar [Tools/Set scale] on this GUI and introduce the value 70 in the edit box which pops up, and validate with [OK]. A set of calibration point coordinates appears in the table [ListCoord] of the GUI.

To see the calibration points on the image, first display the whole image by unselecting [fix] (tag [CheckFixLimits]) in the frame [Axes] of uvmat. Then press [PLOT PTS] in geometry_calib.

To perform the calibration, press [APPLY], first with the default option 'rescale' in calib_type, and confirm by pressing [OK] in the dialog box. The image is now displayed in phys coordinates. A xml file 'images.xml', containing the calibration parameters and reference point coordinates, has been created in the folder 'UVMAT_DEMO01_pair' (it should be identical with the file 'images.ref.xml' put for reference). Note that the xml file name reproduces the name of the folder containing the images, so that images from different cameras should not be put in the same folder.

Translating the coordinates

The origin of the phys coordinates is now arbitrary. It is more convenient to have it for instance at the centre of the cylinder, now at (x,y)=(1.69, 4.05).

To get the precise position of the cylindre, it is useful to introduce a projection circle, using in uvmat the menu bar command Projection [Projection object/ellipse]. In set_object, select [ProjMode]='none', so that the line is just used as a marker, without projection operation. Set XMax=1, YMax=1, the radius of the circle, and the coordinates (1.69, 4.05) of the centre in the table Coord. Then press [REFRESH]. To optimise the visualisation, zoom in and increase the image contrast to MaxA=100.

To shift the coordinates, activate in geometry_calib the menu bar command [Tools/Translate points], and fills (x=-1.69, y=-4.05) in the edit box which pops up. The phys coordinates of the calibration points are then shifted, and a new calibration put the cylindre centre at the origin (0,0).

put in the same folder.

Repeating the calibration

To repeat the calibration for several image series obtained with the same camera at the same position, different methods can be used.

  • Copy the xml to the appropriate location, with the same name (but extension .xml) and path as the flle containing the image series. This is however not appropriate in general as the xml file contains other information, in particular about image timing. 
  • Open with uvmat one of the image of the series to calibrate, select [Tools/geometric calibration], and in the GUI geometry_calib, the menu bar [Import/All], then press [APPLY]. For further repetitions, the GUI geometry_calib can be left opened while new image series are opened, and [APPLY] repeated each time without importing the calibration data again.
  • In case of many image series, use [REPLICATE] instead of [APPLY] in the GUI geometry_calib. Then select the 'campaign' to calibrate, i.e. the folder containing the series of experiments. Then in the new GUI browse_data, select the set of experiments and the corresponding set of data series to which the calibration must apply (this is used like [Open campaign] in uvmat).

Calibration with reference points

The more general method of calibration consists in using a set of reference points whose physical coordinates are known. Open with uvmat an image in 'UVMAT_DEMO06_PIVconvection/Dalsa1' (accessible on http://servforge.legi.grenoble-inp.fr/pub/soft-uvmat/).

Select in the menu bar [Tools/geometric calibration]. Mark the four box corners of the box with the mouse (left hand button). Their coordinates in pixels are displayed in the two last column of the table [ListCoord] in the GUI geometry_calib. To clear the table for corrections push the button [CLEAR_PTS], or for a single line, use the key board 'Delete' button. To improve the position on the image, use the zoom and directional arrows. We find the coordinates of the four calibration points in pixels:

(X,Y)=(80.3, 81.6), (982.3, 86.1), (978.9, 937.4), (71.2, 929.5).

The corresponding physical coordinates are known to be:

(x,y)=(0,0),(58.8,0),(58.8,55.1),(0,55.1), with an origin (0,0) taken at the lower left (and z=0).

Introduce those in the two first columns of the table [ListCoord]. This can be conveniently done by copy-paste Matlab vector x=[0 58.8 58.8 0] in the upper line of the x column, and y=[0 0 55.1 55.1] in the y column (use carriage return to validate the input).

To perform the calibration, press [APPLY], first with the default option 'rescale' in calib_type. The image is now displayed in phys coordinates. We observe that the rectangular frame is slightly rotated. Furthermore the displayed precision, about 3 pixels, is not excellent.

To improve the precision we then apply the option 'linear' in calib_type, which seeks a general linear transform, including rotation. The precision is indeed improved to about 1 pixel. The previous xml file has been saved with a ~, ('Dalsa1.xml~') so it can be reverted in case of error.

Calibration with a target grid

Most precise and general calibration relies on the use of a target grid. As an example, open in uvmat the image ima_6 in 'UVMAT_DEMO07_GeometryCalibration/Dalsa1' (accessible on http://servforge.legi.grenoble-inp.fr/pub/soft-uvmat/). Open the menu bar [Tools/geometric calibration] and pick four corner points ABCD with the mouse define the periphery of the phys grid selected for calibration. The first point A will define the phys axis origin while AB defines the x axis and AD the y axis. AB and DC should be parallel on the phys grid (see fig). Then select [Tools/Detect grid] on the upper menu bar of geometry_calib: you get a new GUI detect_grid in which you define (in phys units) the grid mesh and the positions of the first and last points on each axis. A z position can be defiend as well, do not fill it in this example. The option white markers is selected (by default) indicating that the grid is white (the opposite option would be needed for a grid made of black crosses on a white background). After validation by [OK], the detected grid appears on uvmat (see fig).

If a point is not correct, select the option [CheckEnableMouse] in geometry_calib. Then you can adjust the point marker by selecting it with the (left button) mouse and moving it while keeping the mouse pressed (when adjustement is finished, nselected the option [CheckEnableMouse] to avoid spurious point creation with the mouse).

If the grid image is of poor quality, it is alternatively possble to mark all the points by the mouse, using the [Tools/Create] grid instead of [Tools/Detect grid] in geometry_calib (not convenient in general).

Once the grid has been marked, the calibration can be performed by the press button [APPLY]. We observe that the simple option 'rescale' is not appropriate in this case: a perspective effect is clearly visible, together with a non-linear deformation (grid lines are curved on the image). Therefore select the option '3D_quadr' which applies a 3D projection and quadratic correction. The grid image now appears of good quality in phys coordinates.

Merging the images of several cameras:

3D calibration :

The previous calibration corrects for 3D projection effects and gives some 3D indication. This is however made more precise by introducing different views of the same grid with different orientations, like shown in mages 1 to 5.

z position

Setting laser slices:

Attachments (10)

Download all attachments as: .zip